Registers

Summary

INTR_STATE

Interrupt State Register

• Offset: 0x0
• Reset default: 0x0
• Reset mask: 0xff

Fields

{"reg": [{"name": "upload_cmdfifo_not_empty", "bits": 1, "attr": ["rw1c"], "rotate": -90}, {"name": "upload_payload_not_empty", "bits": 1, "attr": ["rw1c"], "rotate": -90}, {"name": "upload_payload_overflow", "bits": 1, "attr": ["rw1c"], "rotate": -90}, {"name": "readbuf_watermark", "bits": 1, "attr": ["rw1c"], "rotate": -90}, {"name": "readbuf_flip", "bits": 1, "attr": ["rw1c"], "rotate": -90}, {"name": "tpm_header_not_empty", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "tpm_rdfifo_cmd_end", "bits": 1, "attr": ["rw1c"], "rotate": -90}, {"name": "tpm_rdfifo_drop", "bits": 1, "attr": ["rw1c"], "rotate": -90}, {"bits": 24}], "config": {"lanes": 1, "fontsize": 10, "vspace": 260}}

INTR_ENABLE

Interrupt Enable Register

• Offset: 0x4
• Reset default: 0x0
• Reset mask: 0xff

Fields

{"reg": [{"name": "upload_cmdfifo_not_empty", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "upload_payload_not_empty", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "upload_payload_overflow", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "readbuf_watermark", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "readbuf_flip", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "tpm_header_not_empty", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "tpm_rdfifo_cmd_end", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "tpm_rdfifo_drop", "bits": 1, "attr": ["rw"], "rotate": -90}, {"bits": 24}], "config": {"lanes": 1, "fontsize": 10, "vspace": 260}}

INTR_TEST

Interrupt Test Register

• Offset: 0x8
• Reset default: 0x0
• Reset mask: 0xff

Fields

{"reg": [{"name": "upload_cmdfifo_not_empty", "bits": 1, "attr": ["wo"], "rotate": -90}, {"name": "upload_payload_not_empty", "bits": 1, "attr": ["wo"], "rotate": -90}, {"name": "upload_payload_overflow", "bits": 1, "attr": ["wo"], "rotate": -90}, {"name": "readbuf_watermark", "bits": 1, "attr": ["wo"], "rotate": -90}, {"name": "readbuf_flip", "bits": 1, "attr": ["wo"], "rotate": -90}, {"name": "tpm_header_not_empty", "bits": 1, "attr": ["wo"], "rotate": -90}, {"name": "tpm_rdfifo_cmd_end", "bits": 1, "attr": ["wo"], "rotate": -90}, {"name": "tpm_rdfifo_drop", "bits": 1, "attr": ["wo"], "rotate": -90}, {"bits": 24}], "config": {"lanes": 1, "fontsize": 10, "vspace": 260}}

ALERT_TEST

Alert Test Register

• Offset: 0xc
• Reset default: 0x0
• Reset mask: 0x1

Fields

{"reg": [{"name": "fatal_fault", "bits": 1, "attr": ["wo"], "rotate": -90}, {"bits": 31}], "config": {"lanes": 1, "fontsize": 10, "vspace": 130}}

CONTROL

Control register

• Offset: 0x10
• Reset default: 0x10
• Reset mask: 0x33

Fields

{"reg": [{"name": "FLASH_STATUS_FIFO_CLR", "bits": 1, "attr": ["rw1s"], "rotate": -90}, {"name": "FLASH_READ_BUFFER_CLR", "bits": 1, "attr": ["rw1s"], "rotate": -90}, {"bits": 2}, {"name": "MODE", "bits": 2, "attr": ["rw"], "rotate": -90}, {"bits": 26}], "config": {"lanes": 1, "fontsize": 10, "vspace": 230}}

CONTROL . MODE

SPI Device flash operation mode.

Other values are reserved.

CONTROL . FLASH_READ_BUFFER_CLR

Set to clear the read buffer state.

When set to 1, resets the flash read buffer state that tracks the host read address. The reset should only be used when the upstream SPI host is known to be inactive. This function is intended to allow restoring initial values when the upstream SPI host is reset.

This CSR automatically resets to 0.

CONTROL . FLASH_STATUS_FIFO_CLR

Set to clear the flash status FIFO.

When set to 1, resets the flash status FIFO used for synchronizing changes from firmware. The reset should only be used when the upstream SPI host is known to be inactive. This function is intended to allow restoring initial values when the upstream SPI host is reset.

This CSR automatically resets to 0.

CFG

Configuration Register

• Offset: 0x14
• Reset default: 0x0
• Reset mask: 0x100000c

Fields

{"reg": [{"bits": 2}, {"name": "tx_order", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "rx_order", "bits": 1, "attr": ["rw"], "rotate": -90}, {"bits": 20}, {"name": "mailbox_en", "bits": 1, "attr": ["rw"], "rotate": -90}, {"bits": 7}], "config": {"lanes": 1, "fontsize": 10, "vspace": 120}}

STATUS

SPI Device status register

• Offset: 0x18
• Reset default: 0x60
• Reset mask: 0x60

Fields

{"reg": [{"bits": 5}, {"name": "csb", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "tpm_csb", "bits": 1, "attr": ["ro"], "rotate": -90}, {"bits": 25}], "config": {"lanes": 1, "fontsize": 10, "vspace": 90}}

INTERCEPT_EN

Intercept Passthrough datapath.

• Offset: 0x1c
• Reset default: 0x0
• Reset mask: 0xf

Fields

{"reg": [{"name": "status", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "jedec", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "sfdp", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "mbx", "bits": 1, "attr": ["rw"], "rotate": -90}, {"bits": 28}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

ADDR_MODE

Flash address mode configuration

This register shows the current address mode and pending changes. It is updated by the HW when the command phase completes.

• Offset: 0x20
• Reset default: 0x0
• Reset mask: 0x80000001

Fields

{"reg": [{"name": "addr_4b_en", "bits": 1, "attr": ["rw"], "rotate": -90}, {"bits": 30}, {"name": "pending", "bits": 1, "attr": ["ro"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 120}}

ADDR_MODE . pending

SW-originated change is pending.

This bit is 1 whenever the current value of addr_4b_en has yet to sync with the SPI domain. If an EN4B or EX4B command arrives next, the current value in addr_4b_en will be ignored, and the SPI flash command will take priority, with an update to addr_4b_en to match the command’s result.

ADDR_MODE . addr_4b_en

4B Address Mode enable.

This field configures the internal module to receive 32 bits of the SPI commands. The affected commands are the SPI read commands except QPI, and program commands. It is expected for SW to configure this field at the configuration stage and release control to HW until the next reset.

Even though Read SFDP command has address fields, the SFDP command is not affected by this field. The command always parse 24 bits on the SPI line 0 following the SPI command as the address field.

This field has noteworthy read behavior. If a software-initiated change is still pending the sync to the SPI domain, this bit will reflect the value to be sent. Otherwise, this field will reflect the current value observed in the SPI domain.

LAST_READ_ADDR

Last Read Address

This register shows the last address accessed by the host system. It is updated by the HW when CSb is de-asserted.

• Offset: 0x24
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "addr", "bits": 32, "attr": ["ro"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

FLASH_STATUS

SPI Flash Status register.

This register emulates the SPI Flash Status 3, 2, 1 registers. bit [7:0] is for Status register, bit [15:8] is for Status-2 register, and bit [23:16] is for Status-3 register. It is SW responsibility to maintain this register value up to date.

The HW latches the value when SPI Flash transaction begins. Any updates during the transaction will be updated after the transaction is completed.

• Offset: 0x28
• Reset default: 0x0
• Reset mask: 0xffffff

Fields

{"reg": [{"name": "busy", "bits": 1, "attr": ["rw0c"], "rotate": -90}, {"name": "wel", "bits": 1, "attr": ["rw0c"], "rotate": -90}, {"name": "status", "bits": 22, "attr": ["rw"], "rotate": 0}, {"bits": 8}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

FLASH_STATUS . status

Rest of the status register.

Fields other than the bit 0 (BUSY) and bit 1 (WEL) fields are SW-maintained fields. HW just reads and returns to the host system.

• [ 2]: BP0
• [ 3]: BP1
• [ 4]: BP2
• [ 5]: TB
• [ 6]: SEC
• [ 7]: SRP0
• [ 8]: SRP1
• [ 9]: QE
• [11]: LB1
• [12]: LB2
• [13]: LB3
• [14]: CMP
• [15]: SUS
• [18]: WPS
• [21]: DRV0
• [22]: DRV1
• [23]: HOLD /RST

FLASH_STATUS . wel

WEL signal is cleared when CSb is high. SW should read back the register to confirm the value is cleared.

Bit 1 (WEL) is a SW modifiable and HW modifiable field. HW updates the WEL field when WRDI or WREN command is received.

FLASH_STATUS . busy

BUSY signal is cleared when CSb is high. SW should read back the register to confirm the value is cleared.

JEDEC_CC

JEDEC Continuation Code configuration register.

Read JEDEC ID must return the continuation code if the manufacturer ID is not shown in the first page of JEDEC table. This register controls the Continuation Code.

• Offset: 0x2c
• Reset default: 0x7f
• Reset mask: 0xffff

Fields

{"reg": [{"name": "cc", "bits": 8, "attr": ["rw"], "rotate": 0}, {"name": "num_cc", "bits": 8, "attr": ["rw"], "rotate": 0}, {"bits": 16}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

JEDEC_ID

JEDEC ID register.

• Offset: 0x30
• Reset default: 0x0
• Reset mask: 0xffffff

Fields

{"reg": [{"name": "id", "bits": 16, "attr": ["rw"], "rotate": 0}, {"name": "mf", "bits": 8, "attr": ["rw"], "rotate": 0}, {"bits": 8}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

READ_THRESHOLD

Read Buffer threshold register.

• Offset: 0x34
• Reset default: 0x0
• Reset mask: 0x3ff

Fields

{"reg": [{"name": "threshold", "bits": 10, "attr": ["rw"], "rotate": 0}, {"bits": 22}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

MAILBOX_ADDR

Mailbox Base address register.

The mailbox size is fixed. In this version of IP, the size is 1kB. Lower 10 bits of the Mailbox address is tied to 0.

• Offset: 0x38
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "addr", "bits": 32, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

UPLOAD_STATUS

Upload module status register.

• Offset: 0x3c
• Reset default: 0x0
• Reset mask: 0x9f9f

Fields

{"reg": [{"name": "cmdfifo_depth", "bits": 5, "attr": ["ro"], "rotate": -90}, {"bits": 2}, {"name": "cmdfifo_notempty", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "addrfifo_depth", "bits": 5, "attr": ["ro"], "rotate": -90}, {"bits": 2}, {"name": "addrfifo_notempty", "bits": 1, "attr": ["ro"], "rotate": -90}, {"bits": 16}], "config": {"lanes": 1, "fontsize": 10, "vspace": 190}}

UPLOAD_STATUS2

Upload module status 2 register.

This register contains payload related status. payload_depth indicates the payload size (from 0 to 256 bytes).

payload_start_idx indicates the start of the 256B. This stays 0 usually. However, when the SPI host system issues more than 256B of payload in a command, this field may not be 0. For example, if the system issues 258B payload, the payload_depth is 256 (as the IP only holds 256B of payload), the payload_start_idx is 2. SW should read from 2 to 255 then 0 and 1.

• Offset: 0x40
• Reset default: 0x0
• Reset mask: 0xff01ff

Fields

{"reg": [{"name": "payload_depth", "bits": 9, "attr": ["ro"], "rotate": 0}, {"bits": 7}, {"name": "payload_start_idx", "bits": 8, "attr": ["ro"], "rotate": -90}, {"bits": 8}], "config": {"lanes": 1, "fontsize": 10, "vspace": 190}}

UPLOAD_CMDFIFO

Command Fifo Read Port.

• Offset: 0x44
• Reset default: 0x0
• Reset mask: 0xe0ff

Fields

{"reg": [{"name": "data", "bits": 8, "attr": ["ro"], "rotate": 0}, {"bits": 5}, {"name": "busy", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "wel", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "addr4b_mode", "bits": 1, "attr": ["ro"], "rotate": -90}, {"bits": 16}], "config": {"lanes": 1, "fontsize": 10, "vspace": 130}}

UPLOAD_ADDRFIFO

Address Fifo Read Port.

• Offset: 0x48
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "data", "bits": 32, "attr": ["ro"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

CMD_FILTER_0

Command Filter

If a bit in this CSR is 1, then corresponding SPI command w.r.t the bit position among 256 bit is dropped in SPI Passthrough mode.

• Offset: 0x4c
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "filter_0", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_1", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_2", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_3", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_4", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_5", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_6", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_7", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_8", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_9", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_10", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_11", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_12", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_13", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_14", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_15", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_16", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_17", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_18", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_19", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_20", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_21", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_22", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_23", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_24", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_25", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_26", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_27", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_28", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_29", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_30", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_31", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 110}}

CMD_FILTER_1

Command Filter

If a bit in this CSR is 1, then corresponding SPI command w.r.t the bit position among 256 bit is dropped in SPI Passthrough mode.

• Offset: 0x50
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "filter_32", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_33", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_34", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_35", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_36", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_37", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_38", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_39", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_40", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_41", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_42", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_43", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_44", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_45", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_46", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_47", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_48", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_49", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_50", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_51", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_52", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_53", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_54", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_55", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_56", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_57", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_58", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_59", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_60", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_61", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_62", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_63", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 110}}

CMD_FILTER_2

Command Filter

If a bit in this CSR is 1, then corresponding SPI command w.r.t the bit position among 256 bit is dropped in SPI Passthrough mode.

• Offset: 0x54
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "filter_64", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_65", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_66", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_67", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_68", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_69", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_70", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_71", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_72", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_73", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_74", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_75", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_76", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_77", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_78", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_79", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_80", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_81", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_82", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_83", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_84", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_85", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_86", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_87", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_88", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_89", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_90", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_91", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_92", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_93", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_94", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_95", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 110}}

CMD_FILTER_3

Command Filter

If a bit in this CSR is 1, then corresponding SPI command w.r.t the bit position among 256 bit is dropped in SPI Passthrough mode.

• Offset: 0x58
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "filter_96", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_97", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_98", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_99", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_100", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_101", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_102", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_103", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_104", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_105", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_106", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_107", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_108", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_109", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_110", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_111", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_112", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_113", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_114", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_115", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_116", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_117", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_118", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_119", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_120", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_121", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_122", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_123", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_124", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_125", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_126", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_127", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 120}}

CMD_FILTER_4

Command Filter

If a bit in this CSR is 1, then corresponding SPI command w.r.t the bit position among 256 bit is dropped in SPI Passthrough mode.

• Offset: 0x5c
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "filter_128", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_129", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_130", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_131", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_132", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_133", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_134", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_135", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_136", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_137", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_138", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_139", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_140", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_141", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_142", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_143", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_144", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_145", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_146", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_147", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_148", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_149", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_150", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_151", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_152", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_153", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_154", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_155", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_156", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_157", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_158", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_159", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 120}}

CMD_FILTER_5

Command Filter

If a bit in this CSR is 1, then corresponding SPI command w.r.t the bit position among 256 bit is dropped in SPI Passthrough mode.

• Offset: 0x60
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "filter_160", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_161", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_162", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_163", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_164", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_165", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_166", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_167", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_168", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_169", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_170", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_171", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_172", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_173", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_174", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_175", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_176", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_177", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_178", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_179", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_180", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_181", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_182", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_183", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_184", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_185", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_186", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_187", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_188", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_189", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_190", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_191", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 120}}

CMD_FILTER_6

Command Filter

If a bit in this CSR is 1, then corresponding SPI command w.r.t the bit position among 256 bit is dropped in SPI Passthrough mode.

• Offset: 0x64
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "filter_192", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_193", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_194", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_195", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_196", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_197", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_198", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_199", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_200", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_201", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_202", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_203", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_204", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_205", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_206", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_207", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_208", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_209", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_210", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_211", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_212", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_213", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_214", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_215", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_216", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_217", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_218", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_219", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_220", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_221", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_222", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_223", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 120}}

CMD_FILTER_7

Command Filter

If a bit in this CSR is 1, then corresponding SPI command w.r.t the bit position among 256 bit is dropped in SPI Passthrough mode.

• Offset: 0x68
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "filter_224", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_225", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_226", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_227", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_228", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_229", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_230", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_231", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_232", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_233", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_234", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_235", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_236", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_237", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_238", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_239", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_240", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_241", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_242", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_243", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_244", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_245", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_246", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_247", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_248", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_249", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_250", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_251", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_252", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_253", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_254", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "filter_255", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 120}}

ADDR_SWAP_MASK

Address Swap Mask register.

This register is used in the SPI passthrough mode. If any of bits in this register is set, the corresponding address bit in the SPI Read commands is replaced with the data from ADDR_SWAP_DATA.

If 3B address mode is active, upper 8bit [31:24] is ignored.

• Offset: 0x6c
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "mask", "bits": 32, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

ADDR_SWAP_DATA

The address value for the address swap feature.

• Offset: 0x70
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "data", "bits": 32, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

PAYLOAD_SWAP_MASK

Write Data Swap in the passthrough mode.

PAYLOAD_SWAP_MASK CSR provides the SW to change certain bits in the first 4 bytes of the write payload in the passthrough mode.

• Offset: 0x74
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "mask", "bits": 32, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

PAYLOAD_SWAP_DATA

Write Data Swap in the passthrough mode.

PAYLOAD_SWAP_DATA combined with PAYLOAD_SWAP_MASK provides the SW to change certain bits in the first 4 bytes of the write payload in the passthrough mode.

The register should be written in Little-Endian order. [7:0] bits are processed in the first received payload byte. [31:24] bits for the 4th byte.

• Offset: 0x78
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "data", "bits": 32, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

CMD_INFO

Command Info register.

• Reset default: 0x7000
• Reset mask: 0x83ffffff

Instances

Fields

{"reg": [{"name": "opcode", "bits": 8, "attr": ["rw"], "rotate": 0}, {"name": "addr_mode", "bits": 2, "attr": ["rw"], "rotate": -90}, {"name": "addr_swap_en", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "mbyte_en", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "dummy_size", "bits": 3, "attr": ["rw"], "rotate": -90}, {"name": "dummy_en", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "payload_en", "bits": 4, "attr": ["rw"], "rotate": -90}, {"name": "payload_dir", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "payload_swap_en", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "read_pipeline_mode", "bits": 2, "attr": ["rw"], "rotate": -90}, {"name": "upload", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "busy", "bits": 1, "attr": ["rw"], "rotate": -90}, {"bits": 5}, {"name": "valid", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 200}}

CMD_INFO . valid

Set to 1 if the config in the register is valid

CMD_INFO . busy

Set to 1 to set the BUSY bit in the FLASH_STATUS when the command is received. This bit is active only when upload bit is set.

CMD_INFO . upload

Set to 1 to upload the command.

If upload field in the command info entry is set, the cmdparse activates the upload submodule when the opcode is received. addr_en, addr_4B_affected, and addr_4b_forced (TBD) affect the upload functionality. The three address related configs defines the command address field size.

The logic assumes the following SPI input stream as payload, which max size is 256B. If the command exceeds the maximum payload size 256B, the logic wraps the payload and overwrites.

CMD_INFO . read_pipeline_mode

Add 2-stage pipeline to read payload.

If read_pipeline_mode is not set to zero_stages, the read logic adds a 2-stage pipeline to the read data for this command. This read pipeline enables higher throughput for certain read commands in passthrough mode.

payload_dir must be set to PayloadOut: payload_pipeline_en only works with read data. It may be used with any IO mode, but general host compatibility is likely limited to Quad Read. If this pipeline is used for passthrough, the internal SFDP should report 2 additional dummy cycles compared to the downstream flash. SFDP read commands should be processed internally, and dummy_size should still reflect the downstream device’s dummy cycle count.

Other values are reserved.

CMD_INFO . payload_swap_en

Swap the first byte of the write payload.

If payload_swap_en is set, the passthrough logic swaps the first byte of the write payload with DATA_SWAP CSR.

payload_swap_en only works with write data and SingleIO mode. payload_en must be 4’b 0001 and paylod_dir to be PayloadIn.

CMD_INFO . payload_dir

Set to 1 if the command returns data. If 0, the payload sends to the downstream Flash device.

CMD_INFO . payload_en

Payload Enable per SPI lane.

Set to non-zero if the command has payload at the end of the protocol. This field has four bits. Each bit represents the SPI line. If a command is a Single IO command and returns data to the host system, the data is returned on the MISO line (IO[1]). In this case, SW sets payload_en to 4’b 0010.

CMD_INFO . dummy_en

Set to 1 if the command has a dummy cycle following the address field.

CMD_INFO . dummy_size

The number of dummy cycles -1 for the command

CMD_INFO . mbyte_en

If 1, the command has a MByte field following the address field. This is set to 1 for DualIO, QuadIO commands.

CMD_INFO . addr_swap_en

This field is used in the passthrough logic. If this field is set to 1, the address in the passthrough command is replaced to the preconfigured value.

CMD_INFO . addr_mode

Command address mode

A command can have four modes:

• 0: Command does not have an address field
• 1: CFG.addr_4b_en decides the address size (3B/4B)
• 2: Address size is always 3B regardless of CFG.addr_4b_en
• 3: Address size is always 4B regardless of CFG.addr_4b_en

CMD_INFO . opcode

Command Opcode

CMD_INFO_EN4B

Opcode for EN4B.

If the register is active, it affects in flash / passthrough modes.

• Offset: 0xdc
• Reset default: 0x0
• Reset mask: 0x800000ff

Fields

{"reg": [{"name": "opcode", "bits": 8, "attr": ["rw"], "rotate": 0}, {"bits": 23}, {"name": "valid", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

CMD_INFO_EX4B

Opcode for EX4B

• Offset: 0xe0
• Reset default: 0x0
• Reset mask: 0x800000ff

Fields

{"reg": [{"name": "opcode", "bits": 8, "attr": ["rw"], "rotate": 0}, {"bits": 23}, {"name": "valid", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

CMD_INFO_WREN

Opcode for Write Enable (WREN)

• Offset: 0xe4
• Reset default: 0x0
• Reset mask: 0x800000ff

Fields

{"reg": [{"name": "opcode", "bits": 8, "attr": ["rw"], "rotate": 0}, {"bits": 23}, {"name": "valid", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

CMD_INFO_WRDI

Opcode for Write Disable (WRDI)

• Offset: 0xe8
• Reset default: 0x0
• Reset mask: 0x800000ff

Fields

{"reg": [{"name": "opcode", "bits": 8, "attr": ["rw"], "rotate": 0}, {"bits": 23}, {"name": "valid", "bits": 1, "attr": ["rw"], "rotate": -90}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_CAP

TPM HWIP Capability register.

This register shows the features the current TPM HWIP supports.

• Offset: 0x800
• Reset default: 0x660100
• Reset mask: 0x7701ff

Fields

{"reg": [{"name": "rev", "bits": 8, "attr": ["ro"], "rotate": 0}, {"name": "locality", "bits": 1, "attr": ["ro"], "rotate": -90}, {"bits": 7}, {"name": "max_wr_size", "bits": 3, "attr": ["ro"], "rotate": -90}, {"bits": 1}, {"name": "max_rd_size", "bits": 3, "attr": ["ro"], "rotate": -90}, {"bits": 9}], "config": {"lanes": 1, "fontsize": 10, "vspace": 130}}

TPM_CAP . max_rd_size

The maximum read size in bytes the TPM submodule supports. The value is the exponent of the 2.

• 3’b 010: Support up to 4B
• 3’b 011: Support up to 8B
• 3’b 100: Support up to 16B
• 3’b 101: Support up to 32B
• 3’b 110: Support up to 64B

All other values are reserved.

It is not recommended for SW to advertise TPM supporting more than max_rd_size to the South Bridge.

TPM_CAP . max_wr_size

The maximum write size in bytes the TPM submodule supports. The value is the exponent of the 2.

• 3’b 010: Support up to 4B
• 3’b 011: Support up to 8B
• 3’b 100: Support up to 16B
• 3’b 101: Support up to 32B
• 3’b 110: Support up to 64B

All other values are reserved.

It is not recommended for SW to advertise TPM supporting more than max_wr_size to the South Bridge.

TPM_CAP . locality

If 1, the TPM submodule supports 5 Locality. If 0, only one Locality is provided

TPM_CAP . rev

Revision of the TPM submodule

TPM_CFG

TPM Configuration register.

• Offset: 0x804
• Reset default: 0x0
• Reset mask: 0x1f

Fields

{"reg": [{"name": "en", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "tpm_mode", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "hw_reg_dis", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "tpm_reg_chk_dis", "bits": 1, "attr": ["rw"], "rotate": -90}, {"name": "invalid_locality", "bits": 1, "attr": ["rw"], "rotate": -90}, {"bits": 27}], "config": {"lanes": 1, "fontsize": 10, "vspace": 180}}

TPM_CFG . invalid_locality

If 1, TPM submodule returns the invalid data (0xFF) for the out of the max Locality request. If it is a write request, HW still uploads the command and address. SW needs to process the incoming invalid command.

If 0, TPM submodule uploads the TPM command and address. The SW may write 0xFF to the read FIFO.

Note: The TPM submodule uploads the TPM commands that do not fall into the FIFO registers (0xD4_XXXX) regardless of invalid_locality bit.

TPM_CFG . tpm_reg_chk_dis

If 1, the logic does not compare the upper 8 bit of the received address with the TpmAddr constant, D4h.

If this field is 0, the HW uploads the command, address, and write payload to the buffers in case of address that is not 0xD4_XXXX.

TPM_CFG . hw_reg_dis

If 0, TPM submodule directly returns the return-by-HW registers for the read requests.

If 1, TPM submodule uploads the TPM command regardless of the address, and the SW may return the value through the read FIFO.

TPM_CFG . tpm_mode

Configure the TPM mode. 1 for CRB, 0 for FIFO.

If the SW set this field to 1, the HW logic always pushes the command/addr and write data to buffers. The logic does not compare the incoming address to the list of managed-by-HW register addresses.

The invalid locality check still runs based on the invalid_locality configuration.

TPM_CFG . en

If 1, TPM submodule accepts the transactions over SPI

TPM_STATUS

TPM submodule state register.

The TPM_STATUS CSR provides the current TPM status, mostly the buffer and FIFO status.

• Offset: 0x808
• Reset default: 0x0
• Reset mask: 0x7

Fields

{"reg": [{"name": "cmdaddr_notempty", "bits": 1, "attr": ["ro"], "rotate": -90}, {"name": "wrfifo_pending", "bits": 1, "attr": ["rw0c"], "rotate": -90}, {"name": "rdfifo_aborted", "bits": 1, "attr": ["ro"], "rotate": -90}, {"bits": 29}], "config": {"lanes": 1, "fontsize": 10, "vspace": 180}}

TPM_STATUS . rdfifo_aborted

If 1, the last Read FIFO command was aborted.

This bit becomes 1 when a Read FIFO command became active, but the transaction did not complete. An aborted transaction occurs when the host de-asserts CSB without clocking all the requested data. This bit remains 1 until reset, or it will clear automatically after the next valid command is read from TPM_CMD_ADDR.

TPM_STATUS . wrfifo_pending

If 1, the Write FIFO is reserved for software processing.

This bit becomes 1 when a complete write command is received. While it remains 1, subsequent write commands will block at the wait state until it is cleared. Write 0 to release the Write FIFO back to the TPM module.

TPM_STATUS . cmdaddr_notempty

If 1, the TPM_CMD_ADDR has a valid data. This status is reported via the interrupt also.

TPM_ACCESS_0

TPM_ACCESS_x register.

• Offset: 0x80c
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "access_0", "bits": 8, "attr": ["rw"], "rotate": 0}, {"name": "access_1", "bits": 8, "attr": ["rw"], "rotate": 0}, {"name": "access_2", "bits": 8, "attr": ["rw"], "rotate": 0}, {"name": "access_3", "bits": 8, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_ACCESS_1

TPM_ACCESS_x register.

• Offset: 0x810
• Reset default: 0x0
• Reset mask: 0xff

Fields

{"reg": [{"name": "access_4", "bits": 8, "attr": ["rw"], "rotate": 0}, {"bits": 24}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_STS

TPM_STS_x register.

The register is mirrored to all Localities. The value is returned to the host system only when the activeLocality in the TPM_ACCESS_x is matched to the current received Locality.

• Offset: 0x814
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "sts", "bits": 32, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_INTF_CAPABILITY

TPM_INTF_CAPABILITY

• Offset: 0x818
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "intf_capability", "bits": 32, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_INT_ENABLE

TPM_INT_ENABLE

• Offset: 0x81c
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "int_enable", "bits": 32, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_INT_VECTOR

TPM_INT_VECTOR

• Offset: 0x820
• Reset default: 0x0
• Reset mask: 0xff

Fields

{"reg": [{"name": "int_vector", "bits": 8, "attr": ["rw"], "rotate": 0}, {"bits": 24}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_INT_STATUS

TPM_INT_STATUS

• Offset: 0x824
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "int_status", "bits": 32, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_DID_VID

TPM_DID/ TPM_VID register

• Offset: 0x828
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "vid", "bits": 16, "attr": ["rw"], "rotate": 0}, {"name": "did", "bits": 16, "attr": ["rw"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_RID

TPM_RID

• Offset: 0x82c
• Reset default: 0x0
• Reset mask: 0xff

Fields

{"reg": [{"name": "rid", "bits": 8, "attr": ["rw"], "rotate": 0}, {"bits": 24}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_CMD_ADDR

TPM Command and Address buffer

The SW may get the received TPM command and address by readin gthis CSR.

• Offset: 0x830
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "addr", "bits": 24, "attr": ["ro"], "rotate": 0}, {"name": "cmd", "bits": 8, "attr": ["ro"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

TPM_READ_FIFO

TPM Read command return data FIFO.

The write port of the read command FIFO.

• Offset: 0x834
• Reset default: 0x0
• Reset mask: 0xffffffff

Fields

{"reg": [{"name": "value", "bits": 32, "attr": ["wo"], "rotate": 0}], "config": {"lanes": 1, "fontsize": 10, "vspace": 80}}

egress_buffer

SPI internal egress buffer.

The lower 2 kB is for Read content emulating eFlash. The next 1 kB is for the Mailbox buffer. Then the next 256 B is for the SFDP buffer. Finally, the buffer spaces end with a 64 B TPM Read FIFO.

• Word Aligned Offset Range: 0x1000to0x1d3c
• Size (words): 848
• Access: wo
• Byte writes are not supported.

ingress_buffer

SPI internal ingress buffer.

The layout is as follows (starting from offset 0):

• 256 B SFDP buffer

• 32 B CmdFIFO

• 32 B AddrFIFO

• 256 B payload FIFO

• 64 B TPM Write FIFO

• Word Aligned Offset Range: 0x1e00to0x1fbc

• Size (words): 112

• Access: ro

• Byte writes are not supported.